Engineering

Managing stencil life: from tension tests to a closed cleaning loop

Aperture inspection, tension test, inbound, issuing, loading, cleaning — where the stencil record most often breaks.

Read 5 min Author: Baichuan · Reviewed by: Technical Director

A stencil is the only tool in printing that directly determines solder volume. It has no maintenance plan like a machine and no receipt and issue documents like material, so many plants keep it in a single Excel sheet, and who has it, how often it was washed and how much tension is left all depend on memory.

A stencil is not a consumable, it is a ledger object

A stencil has explicit end-of-life criteria: tension falling below the lower limit, aperture deformation, frame damage. Any one of them stops it from being used, and none can be judged from a single use; they need cumulative records.

From receipt to scrap a stencil goes through dozens of issues, loadings, cleanings and removals. If the ledger records only "received" and "scrapped", everything in between is a black hole, and when a problem appears there is no way back to the specific use that caused it.

Five points and what each records

Receipt

A new stencil records: stencil number, applicable models, aperture dimensions, laser-cutting vendor, incoming tension, receipt date.

Tension is measured once at receipt as the baseline. Without a baseline, later decay has nothing to be compared against.

Issue

Issue against a work order, recording the operator's ID, the work order and the machine it goes onto. One stencil can serve several work orders, but the order must be traceable.

Loading

Three things are checked at loading: the stencil number matches the work order, tension is within the allowed range, and the previous cleaning is complete. The third is most often skipped, and only a record can answer whether the last shift washed it.

Cleaning

Cleaning method and frequency come from the process specification, commonly once per shift or once per a set number of boards. After cleaning, record the time, the method (dry, wet, ultrasonic) and who did it.

The value of the cleaning record is the closed loop. If residue is found at loading, the last cleaning can be identified, and the problem has somewhere to land.

Scrap

Scrap states the reason: tension below limit, aperture deformation, frame damage, human damage. The classification is not for people to read but for purchasing and process: if one reason dominates, something upstream is wrong.

Judging tension and apertures

Tension limits differ with stencil size and follow the process specification. Common practice is at least 35 N/cm below 30 cm and at least 40 N/cm above 30 cm, subject to in-house standards.

Check Frequency Criterion Recorded in
Tension Before each loading Not below the process limit Loading record
Aperture visual After each cleaning No clogging, no deformation Cleaning record
Frame and mesh Monthly No cracks, no debonding Periodic check record
Cumulative uses Each loading Within vendor life Ledger total

The key is to record cumulative uses and cumulative cleanings separately. Some plants record only uses, but cleanings affect tension just as much, ultrasonic cleaning in particular.

The thresholds the standards give

Both aperture design and tension limits have published references. IPC-7525, Stencil Design Guidelines, sets out how to calculate aperture area ratio and aspect ratio: below an area ratio of 0.66, solder paste does not release cleanly, and that number has to be calculated at design time rather than adjusted on the line. Tension limits are tiered by frame size and manufacturer specification — the 35 and 40 N/cm in the table above are common values, with the plant process document taking precedence.

Bringing the standard into the ledger turns rule of thumb into a threshold: apertures calculated by area ratio, tension judged at loading, both leaving numbers behind, so decay shows up as a trend instead of being discovered when prints start starving.

References: IPC-7525, Stencil Design Guidelines (ipc.org).

From what we see in implementation, stencil ledgers break in three places:

  1. Issues are not recorded. A stencil is a shared tool, nobody knows who took it, and finding it means searching the whole shop.
  2. Cleaning is not closed. It was washed but not recorded, the next loading cannot confirm the state, so it is washed again and life is consumed for nothing.
  3. Tension tests do not record numbers. It was measured but only marked "pass". Decay cannot be seen, and by the time it fails it is a cliff.

What these three share: the action happened but the data did not stay. A system does not test for people; it binds the result to the stencil number so the next loading can see the last result.

The relation to solder paste

Stencil and solder paste are the two ends of one data chain. The aperture decides solder volume and the paste decides flow, and either going wrong shows up as a print defect. Managed separately, a problem means checking paste first, then the stencil, with two ledgers that do not line up in time.

Put the stencil loading record and the paste issue record on the same timeline and troubleshooting time drops noticeably. For the paste side see solder paste management.

Frequently asked questions

Is stencil life counted in uses or in time

In uses. Sitting idle does not consume life, but the storage environment affects tension, so a stencil out of use for a long time is re-measured before going back on the line.

How often should tension be measured

Before each loading, which is the cheapest and most effective. If that is not possible, at least once per shift, and record the number rather than the word "pass".

Does the cleaning method affect life

Yes. Ultrasonic cleaning is efficient but affects the frame adhesive, and wet cleaning that is not fully dried leaves moisture. Follow the process specification, and always record the method so an anomaly can be located.

How is the ledger kept without a system

One card per stencil, travelling with it: number, incoming tension, loading dates and work orders, cleaning times and methods, tension readings. A card on the stencil rack is more reliable than a central ledger. Once the card runs reliably, consider a system.

FAQ

At what tension should a stencil be taken out of service?
Follow the process specification; common practice is at least 35 N/cm below 30 cm and at least 40 N/cm above 30 cm. What matters is recording the number: "pass" alone makes the decay trend invisible.
Is stencil life counted in uses or in time?
In uses. Sitting idle does not consume life, but long storage affects tension, so tension is re-measured before it goes back on the line.
Why do cleaning records matter?
They let the next loading confirm whether the last cleaning was done and how. Without them the stencil is simply washed again, consuming life, and residue problems cannot be traced to a cause.
Should the stencil ledger be linked to solder-paste records?
Recommended. The aperture decides solder volume and the paste decides flow; either being abnormal shows up as a print defect. On one timeline, troubleshooting time drops clearly.

Related reading

Next

Send us your line's problems

Describe your line's current state and the step that most needs fixing; we'll send a solution outline per process stage within 2 business days.

Address
Building 8, Room 303, Yilisheng Industrial Park, 602 Fengtang Avenue, Tangwei Community, Fuhai Street, Bao'an District, Shenzhen

Shenzhen Baichuan Zhike Technology Co., Ltd. · Since 2015 , serving electronics manufacturers across handsets, tablets, automotive electronics, FPC, WiFi modules, energy storage and more.

Used for this conversation only; never shared externally. By submitting you agree to be contacted about this request.

Questions?